How To Use Campbell Hausfeld Air Compressor

Campbell Hausfeld air compressor is an oiled unit that is designed for them who undertake menial tasks at dwelling. Fifty-fifty for small calibration automotive technicians every bit this compressor tin power impact wrenches, spray guns, and other air tools.

The ambient air contains traces of moisture when the same air get's compressed, the moisture gets condensed. So don't forget to install an air dryer or a water filter, specially when your job requires completely dry air.

In that location'due south a manual/user guide attached to the unit of measurement you buy, which is very, very of import. You lot need to understand all the safe guidelines, precautionary measures get-go, to run the compressor safely and efficiently.

Now allow's see in particular how to unpack, gather, install and operate the Campbell Hausfeld air compressor.

Contents

ane How to Use the Campbell Hausfeld Air Compressor?
- ane.ane Unpacking:
- ane.2 Assembling:
- 1.iii Installation:
  - 1.iii.1 Air Filter.
  - 1.3.2 Electrical wiring.
- i.4 Operation:
  - one.four.ane Main switch.
  - one.four.2 ASME safety valve.
  - 1.4.3 Regulator.
  - i.4.4 Check valve.
  - one.4.5 Exhaust tube.
  - 1.four.6 Drain valve.
  - 1.4.7 Handle.
  - 1.4.viii Operating steps involved:
ii How to connect and disconnect the portable compressor?
- 2.i Disconnecting:
- 2.2 Connecting:
iii Pressure gauges
4 Maintenance
5 Conclusion.

How to Utilise the Campbell Hausfeld Air Compressor?

Unpacking:

I am sure there'south no need to tell you how to unpack.
And so when you are done with the unpacking, check the unit for whatever damage which might accept caused due to transportation.

Afterwards that check the bolts and other fittings, if they are loose so tighten them before yous beginning the unit.

Assembling:

Function of assembling is the lubrication.
When it comes to lubrication, Ever use the oil which is packed with the compressor.

Note: In case there'south no oil with the shipment, then look in the transmission for instructions regarding lubrication.

Also recall non to utilise whatever mutual car oil (due east.chiliad. 10W-30), as these oils consist of additives they get accumulated on the valves thus affecting the life span of the pump.

If you want the pump to concluding long, which I am sure you lot practice, then supplant the oil subsequently running the compressor for the first few hours. Just have to practice it once.

Around 13 ozs (380 ml) is the corporeality of oil needed past your compressor, the level of oil is visible through the sight glass nowadays on the crankcase expanse of the pump.

Annotation: Don't overfill the tank, the oil level should reach "max" nowadays on the sight glass.

Installation:

Air Filter.

Installing an air filter is of utmost importance, it is threaded onto the side of the compressor.

While installing this brand sure that your surrounding is clean, tidy and completely ventilated.

At least twenty inches of altitude should be present between the compressor and the wall, this volition prevent any objects from acting every bit an obstruction.

Electrical wiring.

Depending upon your locality the electrical wiring lawmaking varies, make sure yous know your local code.
Plug, wiring, and protector should be suitable for the compressor's voltage and amperage.
The power string of the compressor has a grounding facility, keep in mind that the electrical outlet is grounded too, equally this helps during curt circuits.

Operation:

Main switch.

Off or Auto switch, when you plow the switch tooff the compressor volition shut downwards, this is what yous should do when you have to either connect or disconnect the power cord.

When you turn the lever to auto the compressor will start compressing the air, and when the tank reaches its max level it automatically shuts down the unit.

ASME safe valve.

In case the tank force per unit area exceeds the maximum preset level, this valve will release the extra air immediately.

Regulator.

This knob controls the air pressure at the release outlet.

Bank check valve.

Information technology's a one-way valve that prevents the backflow of air into the pump.

Exhaust tube.

The job of this tube is to conduct the air from the pump to the check valve, as it happens it gets very hot while the compressor is working, and so avert touching the tube.

Drain valve.

Present at the underside of the tank, use this valve to drain moisture from the tank. Practice information technology regularly to avoid corrosion.

Note: Brand sure the tank pressure is not above ten psi.

Handle.

It is designed to assist you lot to movement your compressor.

Operating steps involved:

Turn the regulator knob to the left to end the airflow.
Attach the air hose with the outlet of the regulator.
Turn the switch to offposition.
Plug the ability string in.
Now turn the switch to theautomobileposition, the compressor will run until the pressure reaches the maximum, then it gets automatically turned off.
Attach any air tool at the cease of the hose.
Lastly, turn the regulator knob to the right side and set the desired pressure for the air tool that you lot are about to use.

How to connect and disconnect the portable compressor?

Disconnecting:

By holding the neckband present on the coupler remove the connecting hose.
Now remove the knob by unscrewing information technology.
Push the larger tank back and then that you tin can pull the small one frontward, now unhook the base of those 2 tanks.
For storage purposes, supersede that knob in the larger tank.

Connecting:

You need to brand sure that the feet of both the tanks are aligned. And so that the foot bracket of small one fits into the foot bracket opening of the large i.
Just every bit before, push the bank and bring the big tank forward to mount the holding pins of the large ones into the holes of a small 1.
Connect the knob, it will secure the large tank with the small-scale tank'southward handle.
Reattach the connecting hose.

Pressure gauges

There are 2 gauges present, one on the left side of the regulator which shows the pressure level going towards hose including any air tool attached to information technology.

Another is present on the correct side of the regulator, which shows the air pressure of the tank.

Maintenance

Pull the ASME safety valve to release the pressure from the unit, afterwards turning the compressor off.
Using the drain valve removes the moisture from the tank, tilt the tank if needed.
Make clean-upwards grit particles from the intake air filter, valve, pump, and air lines.
Replace oil after 50 hours of usage, bleed the oil past removing the oil bleed plug.

Conclusion.

Follow these steps carefully and call up to keep the unit abroad from any spraying expanse.

When your compressor is non in use make sure it is in a dry, absurd place, and hang the disconnected open ends of the hose down to allow whatever moisture to escape.